Windows 10 reached EOS (end of support) on October 14, 2025. If you are on Windows 10, see this article.

Przeszukaj pomoc

Unikaj oszustw związanych z pomocą.Nigdy nie będziemy prosić Cię o dzwonienie na numer telefonu, wysyłanie SMS-ów ani o udostępnianie danych osobowych. Zgłoś podejrzaną aktywność, korzystając z opcji „Zgłoś nadużycie”.

Więcej informacji
Rozwiązane

Force TLS Version Not Working

SiMoto

Hi

I have a problem with Thunderbird which might be a bit niche but here goes...

The first attempt at sending an email fails as TLS Record Layer v1 is used, the mail server sees this and hard resets the connection so sending halts. See attached Wireshark trace screenshot "Failed".

If I retry the send again Thunderbird uses TLS Record Layer v1.3 and the email goes out ok. See attached Wireshark trace screenshot "Success".

If I send another message immediately no problem but if I wait 20-30 minutes the above cycle happens again.

I have set the minimum TLS version in the config to 1.3 (option 4) and restarted Thunderbird but this has not changed anything.

Any ideas how I can fix this? It's a pain because automated replies don't work.

Hi I have a problem with Thunderbird which might be a bit niche but here goes... The first attempt at sending an email fails as TLS Record Layer v1 is used, the mail server sees this and hard resets the connection so sending halts. See attached Wireshark trace screenshot "Failed". If I retry the send again Thunderbird uses TLS Record Layer v1.3 and the email goes out ok. See attached Wireshark trace screenshot "Success". If I send another message immediately no problem but if I wait 20-30 minutes the above cycle happens again. I have set the minimum TLS version in the config to 1.3 (option 4) and restarted Thunderbird but this has not changed anything. Any ideas how I can fix this? It's a pain because automated replies don't work.
Załączone zrzuty ekranu
Przeczytaj tę odpowiedź w całym kontekście

Wybrane rozwiązanie

SiMoto said

It's been doing it for a while but I've only recently had the time to do a lot of troubleshooting. It happens all the time and is easy to replicate if you want more troubleshooting data.

May be best to file a bug report at https://bugzilla.mozilla.org/enter_bug.cgi/.

Wszystkie odpowiedzi (6)

Does that also happen if you start TB in Troubleshoot mode?

It's the same in Troubleshoot Mode.

I don't use any add-ons, my TB install is completely standard.

Another point I should add is that I'm seeing this behavior on more than one machine, the other one is a Raspberry Pi which also has a default TB set-up.

SiMoto said

It's the same in Troubleshoot Mode. I don't use any add-ons, my TB install is completely standard. Another point I should add is that I'm seeing this behavior on more than one machine, the other one is a Raspberry Pi which also has a default TB set-up.

Did this just start, and is it happening all the time?

It's been doing it for a while but I've only recently had the time to do a lot of troubleshooting.

It happens all the time and is easy to replicate if you want more troubleshooting data.

Wybrane rozwiązanie

SiMoto said

It's been doing it for a while but I've only recently had the time to do a lot of troubleshooting. It happens all the time and is easy to replicate if you want more troubleshooting data.

May be best to file a bug report at https://bugzilla.mozilla.org/enter_bug.cgi/.

Zadaj pytanie

Aby odpowiadać na posty, musisz zalogować się na swoje konto. Zadaj pytanie, jeśli nie masz jeszcze konta.